• • • D.I.Y • • • • • • • • • • • • • • • • Reviews • • • • • • • • • Reviews > More • • • • • • • • • • • • • • • • • • • • Articles • • • • • • • • • Misc • • • Contact/Information • • • • • • Blog • • • • Shopping • • • • • • Resources • • • • • • • • • • • • Off topic! • • • • • • • • • • • Ebay Fake Imax RC B610 Pro USB interface. This writeup is about how I manage to get the USB PC interface enabled on a 'Genuine Pro' that I bought from an Ebay store. I bought the battery charger from an Ebay store that stated it as being equipped with a USB interface that could read display and save battery charging data. The charger arrived and I found it to have a mini USB connector but no USB wire or software was included in the package, I contacted the company via Ebay but they couldn't or didn't want to help me with this matter, they just told me that the charger was coming from another supplier. I started to investigate the problem by downloading a few battery charger monitoring applications that I found at various places on the Internet, but without success I also tried loads of different USB Uart drivers still without being able to communicate with the Imax RC B610 Pro charger that I up to now considered as genuine (Due to the hologram sticker and the fact that I could register the device with the serial number!). Above: The holo sticker and a serial number that actually worked!

Ecowater systems water softener manual. • Discard old resin • Save old gravel • Stand tank upright • Place tape over the opening in the product tube • Refill gravel so it covers screen completely • Pour in new resin until tank is 3/4 full. APS TechNotes ECO Water Softeners How to change the resin The basic components of a water softener tank To replace resin in most water softeners • Turn off water • Disconnect plumbing • Unscrew control head • Lay softener tank on side, or over trash can • Insert garden hose • Allow water to rinse the old resin out.

I gave up and opened up the charger and found that EUREKA the chip for the USB Uart was missing on the circuit board and now I wasn't surprised that it didn't work! By searching the WWW i found out that the missing parts of the circuit was an CP2102 and a LM393. The CP2102 is the actual UART (SERIAL to USB converter) and is the essential part to get the charger to communicate with your PC. The LM393 is a comparator and as far as I understand it is only needed if you care about temperature measuring.

Since cheap (read: counterfeit) B6 chargers bought online on the internet cannot be trusted, you will find hereunder the results of my research to recalibrate my IMAX B6AC clone and make it a viable solution. On forums, you can find lots of info about changing the voltage divider resistors inside the charger. IMAX B6AC V2 Balance Charger and Discharger. Among its new features are a micro USB connection for interfacing with the SkyRC ChargeMaster PC software and.

The CP2102 is a tiny surface mount chip that is hard to solder by hand so I went for a different option and bought a ready made CP2102 interface from YES Ebay again;-) I now picked a USB cable with a mini connector and cut it at the PC end (Keeping the wire with the USB mini connector) then soldered the green wire to RXD and the black wire to GND on the USB To TTL board then I went back to my already open 'Genuine' Pro and soldered a jumper wire as shown on the image below. Red jumper soldered to the last leg where the should have been.

And then to the surface mount component right below the edge of the display board of the battery charger. Now just install the UART driver for the and the Battery Monitoring software. Then connect the Mini USB connector to the Pro charger and the UART connector to your PC, now go to the 'Device manager' (Start/Control panel/Device manager) to find out if your UART is recognized. Also make a note of the COM port that has been assigned to your UART (image below). My USB uart was assigned port 7 and seams to work now I start the Charge Monitor software and gets the splash screen below. • Click save and chose where to save your charging log and give it a name. • Select the correct COM port (That you noted in the Device manager.

Word Day of English has relation to the word Deo (Lamp) same word (Deo) is also referred to as god in Latin. Learn Sindhi through our lessons such as alphabet, adjectives, nouns, plural, gender, numbers, phrases, grammar, vocabulary, verbs, exam, audio, translation and much more. For example the word for farmer is derived from the word Aratro of Latin similarly word Harvest is derived from the word Hari (Farmer) of Sindhi. Urdu english bol chal book free download. We will also review some simple grammar rules, practice common phrases, and we will have fun memorizing many important vocabulary lists, and everything else that you see in app. Sindhi has words from many languages in Europe Asia and Middle East.

• Click on Start When you click start you will get this image after a while and hopefully with a yellow connected indicator! Yellow rectangle with connect, yes!

I received the resistor packs (2 of them, as I needed more resistors for my B8), and replaced the resistors in the amplifiers. The B8 uses 8 identical amplifiers for the 8 cells.

(Simple differential amplifiers, LM324 opamp, 2 pcs of 499k and 2 pcs of 249k.) The other B6 resistor values are not applicable in the B8. I didn't reverse engineered the other functions, as the inaccurate balance was the main issue. I kept the box open, if I am boring too much in the weekend, I search for the resistors responsible for the reference voltage, pack voltage etc. The inaccuracy is not too high, so I can live with it too. The balance result is pretty good, the balance error was as high as 50mV, now below 10mV. Thanks for the idea and the resistor kit. I received the resistor packs (2 of them, as I needed more resistors for my B8), and replaced the resistors in the amplifiers.